Installation and daily maintenance of ballistic screen

The ballistic screen is an efficient screening equipment. It uses a specific vibration method to make the material bounce on the screen surface, thereby achieving screening and grading. It has the advantages of simple structure, easy operation, high screening efficiency and low noise, and is widely used in chemical, food, medicine, mining and other industries. The screen of the ballistic screen can be selected according to different material characteristics and screening requirements, and the screening effect can be controlled by adjusting the vibration frequency and amplitude. During use, regular maintenance and care are required to ensure its long-term stable operation. The ballistic screen is an important screening equipment, which is of great significance to improving production efficiency and reducing costs. Regarding the installation and daily maintenance of the ballistic screen, the following are some key steps and precautions:

A. Installation of the ballistic screen

Ballistic Screen

1. Preparation before installation:

a. Check the factory materials of the equipment to ensure that it meets national standards and refuse to use unqualified products.

b. Pay attention to the storage environment of the equipment to prevent rust and aging.

c. Read the installation instructions carefully before installation to ensure that the process is followed.

2. Installation steps:

a. Install the support or hanging device: Shovel the ground flat and install each component in the order of the drawing, paying attention to the actual stiffness of the end face mark.

b. Connect the screen box: Connect the screen box to the support or hanging device, adjust it according to the specified inclination angle, and ensure that the main axis of the screen box is horizontal.

c. Install the motor and triangular tape: Level the motor foundation, correct the level, ensure that the center lines of the corresponding grooves of the two belt wheels coincide, and adjust the tension of the triangular tape.

d. Install and fix the screen surface: Install the screen surface as required to ensure that the screen surface is tensioned and flat.

e. Inspection: Check whether the feed and discharge chutes of the screen and the under-screen funnel collide during operation.

Note: The specific installation steps may vary depending on the equipment model and manufacturer. Please refer to the installation instructions of the specific equipment for operation.

B. Daily maintenance of the ballistic screen

Ballistic Screen

1. Screen surface inspection and tightening:

Regularly check the tension of the screen surface to ensure that the screen surface is tightened and not loose. If the screen surface is found to be damaged, a new screen should be replaced in time.

2. Motor maintenance:

a. Check the motor running status to ensure that the motor has no abnormal sound and abnormal heating.

c. Check the motor bearing temperature regularly. If it is abnormal, add lubricating oil or replace the bearing.

d. Pay attention to the maintenance and maintenance of the motor, and replace damaged motor parts in time.

3. Vibration and noise inspection:

a. Regularly check whether the installation foundation and supporting structure of the equipment are stable.

b. Check whether the key parts such as the bearing seat and drive device of the equipment are loose or damaged.

c. If abnormal vibration or noise is found, the machine should be stopped immediately for inspection and troubleshooting.

4. Cleaning and maintenance:

Ballistic Screen

a. After each use, the internal residue of the equipment should be cleaned.

b. Regularly check and clean the screen blockage to ensure that the screen is unobstructed.

c. When the equipment is running, it should be lubricated frequently and the appropriate lubricating oil should be selected according to the equipment requirements.

5. Regular inspection and record:

a. Strictly follow the equipment maintenance manual for regular inspection and maintenance.

b. Record the results of each inspection and maintenance so as to find and solve problems in time.

PS: The installation and daily maintenance of the ballistic screen are the key to ensure its normal operation and extend its service life. During the installation process, the instructions should be strictly followed to ensure that all parts are installed correctly and tightened reliably. In daily maintenance, the screen surface, motor, vibration and noise should be checked regularly, and the residue inside the equipment and the screen blockage should be cleaned in time to keep the equipment clean and lubricated. At the same time, the results of each inspection and maintenance should be recorded so that problems can be discovered and solved in time.

Author : Serena Chang

Serena Chang is the writer of blog and news column. With more than 10 years of working experience in the machinery industry, she has a comprehensive understanding of environmental protection machinery and is willing to share useful knowledge of environmental protection machinery.